Study on the possibilities of controlling the laser output beam properties by an intracavity deformable mirror

The possibilities of controlling the laser beam properties by a deformable mirror introduced into the laser optical cavity were studied theoretically and experimentally. The experiments were performed under conditions of an industrial high power transverse flow cw CO₂ laser operating with a stable resonator of a folded configuration. A deformable bimorph mirror of a surface profile controlled by the voltage applied to the mirror electrodes is implemented to the laser system as a back cavity mirror or as a one of the inner folding mirrors. The near-and far-field characteristics of the laser beam versus the resonator configuration controlled by the changes of the focal length of the deformable mirror are discussed in the paper. The analysis reveals that the resonator with an inner deformable mirror is much more sensitive to the mirror curvature variations than the resonator in which the deformable mirror is used as a back cavity mirror. The presented results show that dynamic and controllable changes in the resonator properties result in the controlled modification and optimisation of the laser output power and spatial parameters of the laser radiation.     

Separate Polarization Modes Synchronization and Synchronization Switches between Vertical-Cavity Surface-Emitting Lasers

For vertical-cavity surface-emitting lasers (VCSELs) with polarization-rotated feedback, there exist several synchronization types such as synchronizations between total powers and synchronizations between separate polarization modes. Based on the two-mode rate equations, we study and compare numerically the performances of different synchronization types. Our results show that three synchronization types exhibit good performances when their synchronization conditions are satisfied. They are the complete synchronization between total powers, complete synchronization between x-polarized modes, and generalized synchronization between x-polarized and y-polarized modes. The former two types are sensitive to the injection rate and spontaneous emission, while the third type is contrary. Synchronization type with the best performance may switch from one to another, with changing of injection rate and spontaneous emission factor.     

中物院远红外自由电子激光实验研究

中国工程物理研究院基于射频直线加速器技术的远红外自由电子激光(FIR-FEL)实验取得阶段性进展,于2005年3月24晚8时30分首次出光, 并多次重复. 中心波长115μm, 谱宽1%.介绍了实验系统的主要组成部分和主要实验结果.     

介质的非均匀性对高次谐波影响的研究

讨论了气体介质的非均匀性对飞秒激光高次谐波产生过程的可能影响.计算结果表明,采用喷阀技术所提供的气体介质的密度梯度和气体原子运动速度的影响很小,不会产生实验上可观测的效果.这一结果支持了喷气靶在高次谐波产生中的广泛应用 关键词： 高次谐波 气体介质 各向异性 飞秒激光     

Mode beating in spot-size converter lasers

An anomalous modulation in the wavelength spectrum has been observed in lasers with spot-size converters. This intensity modulation is shown to be caused by beating between the fundamental lasing mode and radiation modes in the taper. This results in a periodic modulation in the net gain spectrum, which causes wavelength jumps between adjacent net gain maxima, and a drive current dependent spectral width that is expected to affect system performance. The amplitude of this spectral modulation is reduced significantly by either using an angled rear-facet which reflects the beating radiation modes away from the laser axis, or by using a nonlinear, adiabatic taper.     

抽运激光在光靶中的局域及其对X射线激光特性的影响

新型X射线靶设计为:由SiO2和TiO2组成具有12个周期的一维光子晶体,在它的中间嵌入光靶材料层作为缺陷层,SiO2,TiO2和光靶层的光学厚度分别为λ4、λ4和λ2,λ为抽运激光波长.与普通平板光靶相比,当抽运光垂直照射到这种光靶时,靶层内部的光强将提高2个数量级,所以抽运激光的阈值强度将降低2个数量级,这有利于X射线激光的小型化.在同样的抽运激光照射下,X射线激光的强度将提高4个数量级,转换效率也将提高约4个数量级.由于平均电离度随抽运激光强度的提高而提高,所以采用这种光靶有利于使X射线激光向短波长推进. 关键词： X射线激光 光子晶体 光波局域     

天光一号预放大器中的放大自发辐射效应

 在三维放大自发辐射（ASE）的模拟计算中，计入了侧壁反射效应以及KrF自发辐射的谱线形状（高斯型、洛伦兹型及平顶型）的影响，并对空间网点的影响进行了考察。经过综合分析，给出了ASE对预放大器放大特性影响的上、下限范围。当计入平顶型频谱分布，壁反射系数为 0 .2时，与不计入ASE的情形对比，天光一号预放大器的提取效率下降为35%。     

The Properties of Light Pressure Force with High Order in Laser Fields

1　Ｉｎｔｒｏｄｕｃｔｉｏｎ　　Ｉｎｒｅｃｅｎｔｙｅａｒｓ,ｂｏｔｈｔｈｅｔｈｅｏｒｅｔｉｃａｌａｎｄｅｘｐｅｒｉｍｅｎｔａｌｉｎｖｅｓｔｉｇａｔｉｏｎｓｏｎｌａｓｅｒｃｏｏｌｉｎｇａｎｄｔｒａｐｐｉｎｇｈａｖｅｂｅｃｏｍｅｏｎｅｏｆｔｈｅｍａｊｏｒｆｉｅｌｄｓｉｎａｔｏｍｉｃ,ｍｏｌｅｃｕｌａｒａｎｄｏｐｔｉｃａｌ ｐｈｙｓｉｃｓ[1～ 8] .Ｔｈｅｄｅｖｅｌｏｐｍｅｎｔｏｆｌａｓｅｒｃｏｏｌｉｎｇａｎｄｔｒａｐｐｉｎｇｔｅｃｈｎｏｌｏｇｙｉｓｉｍｐｏｒｔａｎｔｆｏｒｔｈｅａｐｐｌｉｃａｔｉｏｎｓｓｕ…     

激光陀螺磁灵敏度特性研究

分析、计算了激光陀螺的磁灵敏度特性，并进行了磁灵敏度试验.试验结果及分析表明：在腔体加工准确度不变的情况下，采用合理的设计可以大大降低激光陀螺在某些方向上的磁灵敏度，同时磁试验结果对于设计激光陀螺的磁屏蔽结构具有一定的实用价值.     

Ion implantation induced by Cu ablation at high laser fluence

High energy laser plasma-produced Cu ions have been implanted in silicon substrates placed at different distances and angles with respect to the normal to the surface of the ablated target. The implanted samples have been produced using the iodine high power Prague Asterix Laser System (PALS) using 438 nm wavelength irradiating in vacuum a Cu target. The high laser pulse energy (up to 230 J) and the short pulse duration (400 ps) produced a non-equilibrium plasma expanding mainly along the normal to the Cu target surface. Time-of-flight (TOF) technique was employed, through an electrostatic ion energy analyzer (IEA) placed along the target normal, in order to measure the ion energy, the ion charge state, the energy distribution and the charge state distribution. Ions had a Boltzmann energy distributions with an energy increasing with the charge state. At a laser fluence of the order of 6 × 10⁶ J/cm², the maximum ion energy was about 600 keV and the maximum charge state was about 27+.In order to investigate the implantation processes, Cu depth profiles have been performed with Rutherford backscattering spectrometry (RBS) of 1.5 MeV helium ions, Auger electron spectroscopy (AES) with 3 keV electron beam and 1 keV Ar sputtering ions in combination with scanning electron microscopy (SEM). Surface analysis results indicate that Cu ions are implanted within the first surface layers and that the ion penetration ranges are in agreement with the ion energy measured with IEA analysis.